Schedule Today!

Right here in the next paragraph you can locate a bunch of superb expertise with regards to How to Install a Bathtub.

Installing a bathtub isn't exactly brain surgery, yet it does call for strong plumbing, woodworking, and also occasionally, tiling abilities. Replacing an old bathtub with a brand-new one is additionally a moderately challenging job. If the old bathtub is conveniently obtainable, the task can move immediately; if you need to open up a wall surface to get rid of the old bathtub as well as place the brand-new tub, the job is a lot harder. In either instance, the task is within a residence handyman's abilities, although you will certainly need a helper to move out the old tub and set in the new one. Make sure you have certified yourself for the task and are comfortable attempting it. Rather than hiring a service provider to take control of a halfway-completed task, it is much better to think about employing one before you begin. Opportunities are you might need a specialist plumber to make tube links.
This write-up will aid you mount a brand-new tub in your restroom if you have already purchased a new bathtub and also do not need to change the arrangement of your previous water pipelines.
Your devices as well as material list must make up the following:

• New Bathtub


• Hammer


• Pipe Wrenches


• Prybar


• Safety Glasses


• Level


• Pliers


• Flexible Wrench


• Putty Knife


• Screwdriver


• Cold Chisel


• Measuring tape


• Pipe Caps


 

Getting ready for the Installation

To start with, the supporting structure supplied with the bathroom must be fitted (if required) according to the supplier's directions. Next, fit the faucets or mixer to the tub. When suitable the tap block, it is important to make certain that if the tap features a plastic washer, it is fitted in between the bathroom as well as the faucets. On a plastic bathroom, it is also reasonable to fit a supporting plate under the faucets system to stop stress on the bath tub.
Fit the versatile faucet connectors to the bottom of both taps utilizing 2 nuts and olives (in some cases provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet via the hole in the bath. Utilize the nut provided by the maker to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Ensure you make use of all of the provided washers.
Link the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bathroom should now be ready to be suited its last placement.

Removing Old Taps

If you need to replace old taps with new ones as a part of your setup, after that the first thing you must do is separate the water. After doing so, turn on the taps to drain any water staying in the system. The process of eliminating the existing faucets can be rather problematic due to the restricted gain access to that is often the case.
Use a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipes to the taps. Have a fabric all set for the continuing to be water that will certainly come from the pipes. Once the supply pipes have been eliminated, utilize the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the single faucets from transforming during this procedure. As soon as the taps have been eliminated, the holes in the bath/basin will need to be cleansed of any kind of old securing compound.
Before proceeding to fit the brand-new faucets, contrast the pipeline links on the old taps to the new taps. If the old taps are longer than the new faucets, then a shank adapter is required for the new faucets to fit.

Installing the Bath tub

Using both wood boards under its feet, put the tub in the required placement. The wood boards are practical in uniformly spreading the weight of the bathtub over the location of the boards rather than focusing all the weight onto four tiny factors.
The next objective is to guarantee that the bathtub is leveled all round. This can be attained by examining the spirit level and readjusting the feet on the tub up until the spirit level reads degree.
To set up taps, fit all-time low of the outermost flexible faucet adapter to the suitable supply pipeline by making a compression sign up with; then do the exact same for the other tap.
Activate the water system as well as inspect all joints as well as new pipework for leakages and also tighten them if needed. Fill the bath tub and additionally inspect the overflow electrical outlet and the regular outlet for leakages.
Lastly, repair the bathroom paneling as explained in the manufacturer's user's manual. Tiling and securing around the bath tub must wait until the bath tub has actually been used at the very least once as this will certainly settle it into its final placement.

Fitting New Touches

If the tails of the brand-new taps are plastic, after that you will require a plastic port to prevent damages to the thread. One end of the adapter fits on the plastic tail of the faucet and the various other end supplies a connection to the existent supply pipelines.
If you need to fit a monobloc, after that you will call for decreasing couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next off, position the faucet in the mounting opening in the bath/basin ensuring that the washing machines remain in place in between the tap and also the sink. Secure the faucet in place with the maker offered backnut. When the tap is safely in position, the supply pipes can be attached to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with regular tap ports. The previous type needs to be connected to the faucet ends first, tightening just by hand. The supply pipes can later on be connected to the other end. Tighten up both ends with a spanner after both ends have been linked.

Tiling Around the Bath tub

In the area where the bath fulfills the tile, it is needed to secure the joins with a silicone rubber caulking. This is necessary as the fitting can relocate enough to fracture a rigid seal, triggering the water to pass through the wall between the bathroom and the tiling, resulting in difficulties with moisture and also possible leaks to the ceiling listed below.
You can choose from a variety of coloured sealants to assimilate your components and installations. They are marketed in tubes and cartridges, and can securing voids up to a width of 3mm (1/8 inch). If you have a larger space to fill up, you can load it with spins of soaked newspaper or soft rope. Keep in mind to always fill up the bath tub with water prior to securing, to allow for the motion experienced when the bathtub is in use. The sealer can crack fairly very early if you do not think about this movement before securing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are likewise quickly readily available on the market. It is recommended to fit the ceramic tiles making use of waterproof or water resistant glue and also grout.

A Step-by-Step Guide to Installing a Bathtub

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

 

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

 

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

Remove the Existing Bathtub

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

 

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

Choose the Right Bathtub

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

Install the Plumbing and Ledger Board

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

 

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

Install the Bathtub

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

 

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

 

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

Hook up the Plumbing

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

Install the Bathtub Surround

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

 

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

 

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

 

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

Do you appreciate reading up on Installing A Bathtub? Make a remark down below. We will be interested to see your opinions about this blog. Hoping that you visit us again before long. So long as you enjoyed reading our blog post kindly do not forget to pass it around. I enjoy reading our article about Installing A Bathtub.

Schedule Today!